Eaton Powerware 9355 Installation Manual

View and Download Eaton installation and operation manual online. 20/30 kva. UPS pdf manual download. CAUTION: REFER TO OPERATOR’S MANUAL – Refer to your operator’s manual for . Figure 1 shows the Eaton UPS UPS and an optional Extended. © Eaton Corporation. All Rights contained in this manual, but no liability can be accepted for any errors or omission. Figure 5 Powerware kVA and 40 kVA layout: 1:Graphical LCD; 2:XSlot-1; 3:XSlot-2; 4:Fans;. 5:Input.

• Eaton Powerware 9355 Installation Manual Diagram
• Eaton Powerware 9355 Manual

User's Guide. UPS 20 - 40 kVA. 230/400 V 50/60 Hz output. (3-phase input/output). Contained in this manual, but no liability can be accepted for any errors or omission. The right to make design modifications is. EN 62040-1-1 (Safety) and EN 50091-2 (EMC) are available on the web site (http://www.powerware.com).

Follow the instructions on the inside of the door to open or remove the front cover see Figure 28 and Figure Maintenance Bypass Switch Rev D www. The load is now powered by UPS. Safety Warnings Keep unauthorized personnel away from batteries. See Figure 46 on page 60 for the polarity and verify these connections if polarity control is required.

Eaton Powerware 9355 Installation Manual Diagram

EATON USER MANUAL Pdf Download.

NOTE Conduit and wiring supplied by the customer. Remote Monitor Panel Rev D www. It also gives you a complete record of critical power events, and it notifies you of important UPS or power information. Press the button to save the setting. Display Functions As the default eatln after 15 minutes of inactivity, the LCD displays the selectable startup screen.

Eaton 9355 User Manual

The two output neutral terminals are jumpered together; use either manuual of these terminals to make the output neutral connection. M4 Screws Figure 7.

Replace the UPS front door see page manyal Eaton User Manual pages. Page 70 If active, the UPS knows that input is fed from the generator. Instead, they are preventive alarms intended to alert the user. Joining The Cabinets If you have two Options Cabinets, remove the three circular knockouts on the left side of the first Options Cabinet.

Page 23 Slowly roll the cabinet toward the rear of kanual pallet. Unloading The Cabinet s Be sure to retain the rear shipping bracket and hardware for later re-assembly if you plan to permanently mount the cabinet. Page 58 Permanent Mounting Installation Figure Page 11 UPS from virtually any location within the facility.

Slowly roll the cabinet toward the rear of the pallet. Replace the UPS wiring access cover and conduit landing plate.

Eaton Powerware 9355 Manual

EATON INSTALLATION AND OPERATION MANUAL Pdf Download.

The Eaton UPS does not detect plug-and-play hardware. If, in the opinion of Eaton, a Warranted Item is defective and the defect is within the terms of this Warranty, Eaton’s sole obligation will be to repair or replace such defective item including by providing service, parts, and labor, as applicableat the option of Eaton. Parallel Communication Remove the communication wiring access plate from the UPS rear panel and punch a hole in it using a Greenlee punch or similar device see Figure The UPS is now powering the load in Normal mode.

This email address is being protected from spambots. Normally Open Figure Repeat for each additional EBM.

Unfasten the bypass cabinet front door latch and swing the door open see Figure Remove the communication wiring access plate from the UPS rear panel and punch a hole in it using a Greenlee punch or similar device see Figure Page 87 If active, the UPS knows that input is fed from the generator.

Mount eaotn bypass cabinet to the wall and install the conduit. Press and hold the button for three seconds, until the UPS stops beeping. See Figure 44 and Figure 45 for plug-in manhal block locations. Options Cabinet With Mbs Wiring